Most people ask about pass rates for one of two reasons: to decide whether they're ready, or because they've just failed a paper and want to know if that's normal. The honest answer is that the published numbers give you a general picture, not a precise one. Here's what that picture looks like, where it comes from, and why you shouldn't lean on any single percentage.
The short version. Historically, somewhere around two in three to three in four power engineering exam attempts pass, depending on the class and the paper. Of the 4th to 1st Class levels, 2nd Class has been the toughest to get through. The most detailed numbers available are several years old and from one province, so treat them as a rough guide to the difficulty, not a prediction of your odds.
Where the numbers come from
The most detailed public figures we know of are ABSA's Alberta Power Engineer Examination & Certification Statistics report, which covers exams written in Alberta from 2015 to 2019. As far as we can find, no other jurisdiction publishes comparable detail, and no newer breakdown has been released publicly.
Three things to keep in mind when you read them:
- They count exam attempts, not people. Someone who wrote a paper twice shows up twice.
- They're from one province. The exams are standardized through SOPEEC, but candidate pools, training routes and timing differ between jurisdictions.
- They're from 2019 and earlier. A lot has changed since. More on that below.
The general picture by class
Rather than quote one year, here's the range of yearly pass rates each class saw across those five years in Alberta:
| Class | Yearly pass rate, 2015–2019 | In plain terms |
|---|---|---|
| 5th Class | roughly 50% to 70% | Wide swings year to year, often around 60% |
| 4th Class | roughly 66% to 78% | About two in three to three in four attempts pass |
| 3rd Class | roughly 75% to 85% | Historically the highest pass rates |
| 2nd Class | roughly 56% to 69% | The lowest of the 4th to 1st Class levels in four of the five years |
| 1st Class | roughly 64% to 75% | Small numbers of candidates, a lot of variation by paper |
Source: ABSA, Alberta Power Engineer Examination & Certification Statistics, 1st to 5th Class, 2015–2019. Ranges are the lowest and highest yearly class figures in the report, rounded.
Patterns that held across the papers
- Part A has generally been harder than Part B at 1st and 2nd Class. The theory and calculation papers saw lower pass rates than the equipment and operation papers in most years. At 1st Class, the first two Part A papers were the lowest in the whole system, often around half.
- 2nd Class Part A was the steepest step. From 2015 to 2018, 2A1 and 2A2 sat at roughly half of attempts passing, before improving in 2019.
- 3rd Class was the most consistent level, with most papers in the 70s and 80s most years.
- Every level had a meaningful failure rate. Even the best-performing class in its best year saw about one attempt in seven fail. No paper is a formality.
Why you shouldn't read too much into them
The exams have changed since
The data stops in 2019. Since then, the 2nd Class papers have all moved to multiple choice (2A1 was the last, on January 1, 2025), and 1B4 moved to multiple choice in January 2026. A multiple-choice paper and a written paper are different tests: no partial marks for good method, but no essay writing either. Pass rates from the old formats don't transfer cleanly to the new ones.
Every sitting is a different version
Each paper is set in several versions through the year, so the mix of questions, and how hard a particular sitting feels, varies. A pass rate is an average over all of them.
The averages hide who's writing
The figures mix first-time writers with rewrites, program students with self-study candidates, and people who prepared for months with people who booked on short notice. Your odds depend far more on your own preparation than on the average.
What it means for you
- Take the 65% pass mark seriously. It sounds low until you're under time pressure on a calculation question. Aim to score comfortably above it in practice, not just at it.
- Use practice exams as your real indicator. Your own scores on timed, full-length practice papers tell you far more about your chances than any published pass rate.
- Give the theory papers extra time. Historically the Part A papers have been where candidates struggle most.
- If you've failed one, you're in a lot of company. A fail tells you where to focus, not that you can't pass. See what to do if you've failed a power engineering exam twice.
To see where the questions on each paper typically come from, read the SOPEEC exam breakdown by chapter.
Frequently asked questions
What's the pass mark?
65% on every SOPEEC paper, at every class.
Is there more recent pass rate data?
Not publicly, as far as we can find. ABSA's 2015–2019 report is the most detailed published breakdown. If you need current figures for your jurisdiction, ask your jurisdiction's exam office directly.
Which paper is the hardest?
Historically, the lowest pass rates were on the first two 1st Class Part A papers and on the 2nd Class Part A papers. Which one is hardest for you depends on your background. Candidates from a mechanical or boiler background often find the electrical content hardest, for example.
Do pass rates differ between provinces?
Probably somewhat, but there's no reliable published comparison. The exams themselves are standardized through SOPEEC.